ROS 2 on Kubernetes: a simple talker and listener setup

Kubernetes and robotics make a great match. However, robots running ROS2 can be tricky to set up with individual components on Kubernetes. In this second part of our blog series about running ROS 2 on Kubernetes, we set up a simple, scalable talker / listener system using MicroK8s on Ubuntu. In order to understand some of the design choices for this configuration, be sure to review part one, “Exploring ROS 2 with Kubernetes“.

MicroK8s brings a full Kubernetes install to your machine with a single command and the baseline ROS 2 Foxy docker image fits neatly into the Kubernetes configuration. Our challenge is to configure these projects to all work nicely together.

This configuration creates ROS nodes in pods, and each pod runs a single docker container. The container is the official baseline ROS Foxy docker image maintained by Open Robotics. We launch two talkers and one listener which can be scaled up and down. Networked ROS devices outside the Kubernetes host can also access the ROS graph.

Before you begin

The only hardware needed to run this demo is an x86 workstation running 64-bit Ubuntu 20.04. This will serve as the Kubernetes host.

Each pod will have its own network address; reserve at least five IP addresses exclusively for Kubernetes. Consider reserving ten or more addresses to explore scaling up the demo.

Multus on MicroK8s

The Multus Container Network Interface (CNI) allows the definition of multiple network interfaces for use within Kubernetes. As discussed in part 1, each pod will need to access the host network, and multus adds an interface for that purpose. Multus acts as a CNI manager, enabling use of different network plugins. The ROS 2 prototype uses the default initial interface, and adds a second MacVLAN network to our pods.

K8s Deployments

Deployments define the desired state for one or more pods (e.g. container configurations). Deployments assist in scaling the number of running pods up and down. The prototype configuration defines a talker deployment and a listener deployment, and each can be scaled to create additional talker or listener pods.

Set up the MicroK8s node

A single MicroK8s installation command brings a full Kubernetes installation onto your host. After installing MicroK8s, add your user account to the microk8s group to run most Kubernetes without requiring sudo access.

sudo snap install microk8s --classic
sudo usermod -a -G microk8s $USER
sudo chown -f -R $USER ~/.kube

MicroK8s only installs the basic software needed to run on your host. However, in order to overcome challenges identified in part one of this series, enable the CoreDNS and Multus addon services with the following command:

microk8s enable dns multus

Next, verify that MicroK8s is started and healthy. An initial installation takes time to start as infrastructure service containers are downloaded and configured. The command microk8s status should show that MicroK8s is running, and the command microk8s.kubectl get all should show a single active kubernetes service.

Start the K8s ROS2 cluster

Download the ros-talker-listener-demo.yaml prototype from github:

wget https://raw.githubusercontent.com/canonical/robotics-blog-k8s/main/ros-talker-listener-demo.yaml

Modify this prototype to fit your network configuration. Use the ip route command on your K8s host to identify your primary network interface, network subnet and default gateway (eth0, 192.168.0.0/16 and 192.168.1.1 respectively as retrieved from the image below).

Open ros-demo.yaml in a text editor and update the NetworkAttachmentDefinition spec in lines 6 through 23 to match your environment:

• Make sure that the network interface listed in line 10, "master": "eth0", matches the network interface identified above.
• Update "subnet": "192.168.0.0/16" to the network subnet identified above.
• Set the rangeStart and rangeEnd IP addresses on lines 18 and 19 to the range of addresses reserved for your pods.
• Change "gateway": "192.168.1.1" in line 20 to the gateway identified above.

Save your changes.

Now start the single node ROS 2 cluster with the command

microk8s.kubectl apply -f ros-demo.yaml

Cluster configuration, explained

When you apply this configuration, the following happens:

• Multus defines a network attachment that uses MacVLAN to bridge pods to your host network interface. In addition to the default network interfaces, each container now also receives this MacVLAN interface with access to the host network.
• Kubernetes deploys two ros-talker pods running publisher.py. This script publishes a ROS 2 message on the microk8s-chatter topic which includes the source container, process ID and message serial number.
• Kubernetes deploys a single ros-listener pod running subscriber.py. This script logs each message received on the microk8s-chatter topic.

Let’s take a more detailed look at the file. Kubernetes configuration files follow standard YAML syntax. This configuration has distinct sections (YAML documents) separated with three dashes.

NetworkAttachmentDefinition my-network

apiVersion: "k8s.cni.cncf.io/v1"
kind: NetworkAttachmentDefinition
metadata: name: my-network

The first section invokes Multus to define a network attachment object. This attachment is named my-network.

The specification for the object named my-network follows the definition:

spec: config: '{ "cniVersion": "0.3.0", "name": "my-network", "type": "macvlan", "master": "eth0", "mode": "bridge", "isDefaultgateway": true,

The type field specifies this as a macvlan network connection. Additional fields follow the CNI plugins format from CNCF. See the MacVLAN documentation for additional options.

By using a MacVLAN adapter, the Pod receives a unique MAC address and IP address. The pod’s network interface is bridged to the host’s master network interface.

The MacVLAN configuration put all the pods directly on the host network; however, consider exploring different networking options of this does not fit your environment. Other CNI plugins such as calico, flannel and ipvlan are available, find them in the /var/snap/microk8s/current/opt/cni/bin directory.

The MacVLAN specification also requires an IP Address Management (IPAM) configuration section:

 "ipam": { "type": "host-local", "ranges": [ [ { "subnet": "192.168.0.0/16", "rangeStart": "192.168.1.160", "rangeEnd": "192.168.1.180", "gateway": "192.168.1.1" } ]

These settings configure the pod network interfaces assigned the my-network network attachment. Each should use the same default gateway and subnet mask as your host’s network interface and other devices on your network. Here we also define the pool of IP addresses which will be assigned to pods.

Deployment ros-talker-deployment

The next section of the configuration file outlines the first Kubernetes deployment. Although we could create individual pods, when we create a deployment we let Kubernetes handle the details of where, when and how to start up the pod.

apiVersion: apps/v1
kind: Deployment
metadata: name: ros-talker-deployment labels: app: ros-talker

The first section contains the preamble used to create a deployment named ros-talker-deployment and assign it a metadata application label of ros-talker.

Kubernetes labels assign arbitrary key/value attributes to objects; in this case, to a deployment. Although labels do not change the object’s behaviour, they can be used as selectors for efficient access and manipulation of objects.

spec: replicas: 2

The specification for this deployment begins by calling for exactly two instances (replicas) of this deployment. The number of replicas (and many other deployment properties) can be modified while the pod is running.

 selector: matchLabels: app: ros-talker template: metadata: labels: app: ros-talker

The spec next includes a selector which associates this specification to the ros-talker deployment. Similarly the template is labeled as part of the ros-talker app.

 annotations: k8s.v1.cni.cncf.io/networks: my-network

A CNI annotation lets multus configure networking properly. The annotation key k8s.v1.cni.cncf.io/networks binds the network attachment my-network to any pods created with this deployment. The MacVLAN interface will now be added to the ros-talker pod.

 spec: containers: - name: talker image: ros:foxy

The pod spec lies within the deployment spec. This follows standard container definition syntax for kubernetes. This spec creates a container with the base name talker using the standard ros:foxy docker image.

 command: ["/bin/bash", "-c"] args: ["source /opt/ros/foxy/setup.bash && apt update && apt install -y curl && curl https://raw.githubusercontent.com/canonical/robotics-blog-k8s/main/publisher.py > publisher.py && /bin/python3 publisher.py talker"]

The final two lines of this section define the behavior for the ROS Foxy container after starting. The container runs a bash shell to spin up a ROS talker:

1. First source the ROS setup file to set the proper environment
2. Update apt and install curl
3. Use curl to download the publisher.py demo python script from github.
4. Finally run the downloaded publisher.py script

Typically much of this work would be included as a custom container image; however, for simplicity of this demo the install is done after launch. The container continues to run the publisher script until stopped. This script publishes a message on the microk8s-chatter ROS 2 topic with data to help identify the pod generating the messages. For more information about the publisher.py script, please see the source code.

Deployment ros-listener-deployment

The third section closely follows the talker deployment.

apiVersion: apps/v1
kind: Deployment
metadata: name: ros-listener-deployment labels: app: ros-listener annotations: k8s.v1.cni.cncf.io/networks: my-network

The only difference between the listener and the talker above is to change the names and labels.

spec: replicas: 1

This configuration starts only a single replica; additional listener pods can be created by scaling the number of replicas at any time.

 selector: matchLabels: app: ros-listener template: metadata: labels: app: ros-listener annotations: k8s.v1.cni.cncf.io/networks: my-network

The listener pod receives the same network configuration as the talker pod which allows both to communicate freely.

 spec: containers: - name: listener image: ros:foxy command: ["/bin/bash", "-c"] args: ["source /opt/ros/foxy/setup.bash && apt update && apt install -y curl && curl https://raw.githubusercontent.com/canonical/robotics-blog-k8s/main/subscriber.py > subscriber.py && /bin/python3 subscriber.py listener"]

The listener pod downloads and runs the subscriber.py python script. Similar to publisher.py, this script logs the receiving host’s name in addition to the message received.

Explore the Kubernetes cluster

Are you sure your nodes are running? The commands below help monitor the state of the MicroK8s cluster and diagnose any potential problems.

Check the status

It may take a few minutes to download and launch the ROS 2 container on your first startup as MicroK8s downloads the ROS Foxy image. Use the command microk8s.kubectl get all to check the status. This should return results similar to the following:

NAME READY STATUS RESTARTS AGE
pod/ros-talker-deployment-6c447f496c-7r5mq 0/1 ContainerCreating 0 41s
pod/ros-service-deployment-745cd86b67-lprgg 0/1 ContainerCreating 0 40s
pod/ros-talker-deployment-6c447f496c-8cx27 0/1 ContainerCreating 0 40s
pod/ros-listener-deployment-575bfddd-qsm77 0/1 ContainerCreating 0 40s NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE
service/kubernetes ClusterIP 10.152.183.1 <none> 443/TCP 9m24s NAME READY UP-TO-DATE AVAILABLE AGE
deployment.apps/ros-talker-deployment 0/2 2 0 41s
deployment.apps/ros-listener-deployment 0/1 1 0 41s
deployment.apps/ros-service-deployment 0/1 1 0 41s NAME DESIRED CURRENT READY AGE
replicaset.apps/ros-talker-deployment-6c447f496c 2 2 0 41s
replicaset.apps/ros-listener-deployment-575bfddd 1 1 0 41s
replicaset.apps/ros-service-deployment-745cd86b67 1 1 0 40s

Status changes to Running as the download completes and each container launches.

Monitor pod activity

Confirm that the ROS 2 listener is receiving messages with the following command:

microk8s.kubectl logs --follow -l app=ros-listener

This uses the ros-listener label to find the listener container, and follows the logs generated by the listener. Output should be similar to the following:

...
[INFO] [1603896877.714659178] [minimal_subscriber]: listener:ros-listener-deployment-575bfddd-qsm77:1: "talker:ros-talker-deployment-6c447f496c-7r5mq:1: 347"
[INFO] [1603896877.874107325] [minimal_subscriber]: listener:ros-listener-deployment-575bfddd-qsm77:1: "talker:ros-talker-deployment-6c447f496c-8cx27:1: 342"
...

This shows the listener node receiving messages from two talkers. Host names from the logs matches container names from the get all command above.

Explore logs from each of the pods using the microk8s.kubectl logs command.

Run a command on a container

Sometimes it may be useful to run a command directly on a container within a pod. Use the following command to launch a bash shell on the talker container:

microk8s.kubectl exec pod/ros-talker-deployment-6c447f496c-7r5mq --stdin --tty -- /bin/bash

From here you can interact with a familiar ROS 2 environment:

root@ros-talker-deployment-6c447f496c-7r5mq:/# source /opt/ros/foxy/setup.bash root@ros-talker-deployment-6c447f496c-7r5mq:/# ros2 topic list
/microk8s-chatter
/parameter_events
/rosout
root@ros-talker-deployment-6c447f496c-7r5mq:/# ros2 topic info /microk8s
Type: std_msgs/msg/String
Publisher count: 2
Subscription count: 1

Start and stop pods

In order to bring up more talker or listener nodes, dynamically scale the deployment by adding replicas. Follow the listener logs, and open a second terminal session to increase the number of talkers to eight total pods:

microk8s.kubectl scale deployment ros-talker-deployment --replicas=8

Each new pod receives its own IP address and joins the ROS graph by talking on the /microk8s topic. Watch as they begin sending messages to the listener pod. To reduce the number of talkers, simply issue the same command with the desired number of replicas. Microk8s will shut down containers and pods which are no longer needed.

Similarly, an individual pod can be deleted by name with the following command:

microk8s.kubectl delete pod/ros-service-deployment-745cd86b67-lprgg

In conclusion

This configuration should get you started working on your single node Kubernetes cluster. Become familiar with your setup by running different commands, scaling deployments and running commands directly on pods.

In our next post we’ll take the next step to add two additional K8s nodes and distribute our ROS system across three different computers.